A nucleic acid-based surface-enhanced Raman scattering of gold nanorods in N-gene integrated principal component analysis for COVID-19 detection.

A rapid, simple, sensitive, and selective point-of-care diagnosis tool kit is vital for detecting the coronavirus disease (COVID-19) based on the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) strain. Currently, the reverse transcriptase-polymerase chain reaction (RT-PCR) is the best technique to detect the disease. Although a good sensitivity has been observed in RT-PCR, the isolation and screening process for high sample volume is limited due to the time-consuming and laborious work. This study introduced a nucleic acid-based surface-enhanced Raman scattering (SERS) sensor to detect the nucleocapsid gene (N-gene) of SARS-CoV-2. The Raman scattering signal was amplified using gold nanoparticles (AuNPs) possessing a rod-like morphology to improve the SERS effect, which was approximately 12-15 nm in diameter and 40-50 nm in length. These nanoparticles were functionalised with the single-stranded deoxyribonucleic acid (ssDNA) complemented with the N-gene. Furthermore, the study demonstrates method selectivity by strategically testing the same virus genome at different locations. This focused approach showcases the method's capability to discern specific genetic variations, ensuring accuracy in viral detection. A multivariate statistical analysis technique was then applied to analyse the raw SERS spectra data using the principal component analysis (PCA). An acceptable variance amount was demonstrated by the overall variance (82.4 %) for PC1 and PC2, which exceeded the desired value of 80 %. These results successfully revealed the hidden information in the raw SERS spectra data. The outcome suggested a more significant thymine base detection than other nitrogenous bases at wavenumbers 613, 779, 1219, 1345, and 1382 cm-1. Adenine was also less observed at 734 cm-1, and ssDNA-RNA hybridisations were presented in the ketone with amino base SERS bands in 1746, 1815, 1871, and 1971 cm-1 of the fingerprint. Overall, the N-gene could be detected as low as 0.1 nM within 10 mins of incubation time. This approach could be developed as an alternative point-of-care diagnosis tool kit to detect and monitor the COVID-19 disease.

Characteristics of algal-bacterial aerobic granular sludge treating real wastewater: Effects of algal inoculation and alginate-like exopolymers recovery.

Limited information is available on the characteristics of algal-bacterial aerobic granular sludge (AGS) treating real wastewater, especially on its alginate-like exopolymers (ALE) production. In addition, the effect of target microalgae species inoculation on the system performance has not been fully understood. This study aimed to reveal the effect of microalgae inoculation on the characteristics of algal-bacterial AGS and its ALE production potential. Two photo-sequencing batch reactors (PSBR) were employed, namely R1 with activated sludge and R2 with Tetradesmus sp. and activated sludge being inoculated, respectively. Both reactors were fed with locally sourced municipal wastewater and operated for 90 days. Algal-bacterial AGS were successfully cultivated in both reactors. No significant difference was observed between the performances of R1 and R2, reflecting that the inoculation of target microalgae species may not be crucial for the development of algal-bacterial AGS when treating real wastewater. Both reactors achieved an ALE yield of about 70 mg/g of volatile suspended solids (VSS), indicating that a substantial amount of biopolymer can be recovered from wastewater. Interestingly, boron was detected in all the ALE samples, which might contribute to granulation and interspecies quorum sensing. The enrichment of lipids content in ALE from algal-bacterial AGS treating real wastewater reveals its high resource recovery potential. Overall, the algal-bacterial AGS system is a promising biotechnology for simultaneous municipal wastewater treatment and resource (like ALE) recovery.

Micro and macro analysis of restaurant wastewater containing fat, oil, grease (FOG): An approach based on prevention, control, and sustainable management.

The number of restaurants is increasing day by day in almost all the developing countries, causing the increase in the generation of restaurant wastewater. Various activities (i.e., cleaning, washing, and cooking) going on in the restaurant kitchen lead to restaurant wastewater (RWW). RWW has high concentrations of chemical oxygen demand (COD), biochemical oxygen demand (BOD), nutrients such as potassium, phosphorus, and nitrogen, and solids. RWW also contains fats, oil, and grease (FOG) in alarmingly high concentration, which after congealing can constrict the sewer lines, leading to blockages, backups, and sanitatry sewer overflows (SSOs). The paper provides an insight to the details of RWW containing FOG collected from a gravity grease interceptor at a specific site in Malaysia, and its expected consequences and the sustainable management plan as prevention, control, and mitigation (PCM) approach. The results showed that the concentrations of pollutants are very high as compared to the discharge standards given by Department of Environment, Malaysia. Maximum values for COD, BOD and FOG in the restaurant wastewater samples were found to be 9948, 3170, and 1640 mg/l, respectively. FAME and FESEM analysis are done on the RWW containing FOG. In the FOG, palmitic acid (C16:0), stearic acid (C18:0), oleic acid (C18:1n9c), linoleic acid (C18:2n6c) are the dominant lipid acids with a maximum of 41, 8.4, 43.2, and 11.5%, respectively. FESEM analysis showed formation of whitish layers fprmed due to the deposition of calcium salts. Furthermore, a novel design of indoor hydromechanical grease interceptor (HGI) was proposed in the study based on the Malaysian conditions of restaurant. The HGI was designed for a maximum flow rate of 132 L per minute and a maximum FOG capacity of 60 kg.

Algal-bacterial aerobic granular sludge for real municipal wastewater treatment: Performance, microbial community change and feasibility of lipid recovery.

Despite various research works on algal-bacterial aerobic granular sludge for wastewater treatment and resource recovery processes, limited information is available on its application in real wastewater treatment in terms of performance, microbial community variation and resource recovery. This study investigated the performance of algal-bacterial aerobic granular sludge on real low-strength wastewater treatment in addition to the characterization of microbial community and fatty acid compositions for biodiesel production. The results demonstrated 71% COD, 77% NH4+-N and 31% phosphate removal efficiencies, respectively. In addition, all the water parameters successfully met the effluent standard A, imposed by the Department of Environment (DOE) Malaysia. Core microbiome analyses revealed important microbial groups (i.e., Haliangium ochraceum, Burkholderiales and Chitinophagaceae) in bacterial community. Meanwhile the photosynthetic microorganisms, such as Oxyphotobacteria and Trebouxiophyceae dominated the algal-bacterial aerobic granular sludge, suggesting their important roles in granulation and wastewater treatment. Up to 12.51 mg/gSS lipid content was recovered from the granules. In addition, fatty acids composition showed high percetages of C16:0 and C18:0, demonstrating high feasibility to be used for biodiesel production application indicated by the cetane number, iodine value and oxidation stability properties.

Commercialization potential of agro-based polyhydroxyalkanoates biorefinery: A technical perspective on advances and critical barriers.

The exponential increase in the use and careless discard of synthetic plastics has created an alarming concern over the environmental health due to the detrimental effects of petroleum based synthetic polymeric compounds. Piling up of these plastic commodities on various ecological niches and entry of their fragmented parts into soil and water has clearly affected the quality of these ecosystems in the past few decades. Among the many constructive strategies developed to tackle this global issue, use of biopolymers like polyhydroxyalkanoates as sustainable alternatives for synthetic plastics has gained momentum. Despite their excellent material properties and significant biodegradability, polyhydroxyalkanoates still fails to compete with their synthetic counterparts majorly due to the high cost associated with their production and purification thereby limiting their commercialization. Usage of renewable feedstocks as substrates for polyhydroxyalkanoates production has been the thrust area of research to attain the sustainability tag. This review work attempts to provide insights about the recent developments in the production of polyhydroxyalkanoates using renewable feedstock along with various pretreatment methods used for substrate preparation for polyhydroxyalkanoates production. Further, the application of blends based on polyhydroxyalkanoates, and the challenges associated with the waste valorization based polyhydroxyalkanoates production strategy is elaborated in this review work.

The role of restaurant wastewater for producing bioenergy towards a circular bioeconomy: A review on composition, environmental impacts, and sustainable integrated management.

Population inflation has led to the unprecedented increase in urbanization, thus causing negative impacts on environmental sustainability. Recently, there is an upsurge in the number of restaurants due to the changing lifestyles of the people round the globe. For instance, there were 167,490 food and beverage establishments in 2015, representing an annual growth rate of 5.1% since 2010 in Malaysia. The rapid growth of restaurants has implicated a negative impact due to the generation of highly polluted restaurant wastewater (RWW). RWW is mainly generated during the cooking, washing, and cleaning operations. RWW typically contain fat, oil, and grease (FOG) resulting from residues of meat, deep-fried food, baked items and butter, and has caused serious blockages of sewer due to clogging and eventually sewage backup. This has increased the required frequency of cleaning and sanitary sewer overflows (SSOs). Results from the previous studies have shown that FOG can be treated using physical, chemical, and biological processes. Different technologies have been applied for the treatment of FOG and other pollutants (COD, BOD, SS and NH4-N) present in RWW. Therefore, this review aims to provide an in-depth understanding of the characteristics of RWW, chemical and physical characteristics of FOG with the mechanism of its formation and utilization for biocomposites, biogas and biodiesel productions for circular bioeconomy. Besides, this review has discussed the potential treatment technologies comprehensively for RWW which is currently remain understudied. Integrated sustainable management of FOG with technoeconomic analysis of bioproducts, sustainable management with international initiatives and previous studies are also summarized. Hence, this review aims towards providing better alternatives in managing RWW at sources, including its treatment and potential of its biorefinery, therefore eventually contributing towards environmental sustainability.

Future trends and patterns in leachate biological treatment research from a bibliometric perspective.

Leachate has become a great deal of concern due to its complex properties which are primarily caused by the high concentrations of organics and ammonia. Thus, proper leachate treatment is required prior to its discharge. Leachate can be treated in various ways, and biological treatment is one of the approaches. This treatment has been shown to be both effective and cost-efficient while offering the possibility of resource recovery in the form of bioenergy. In this study, the underlying patterns in publications related to leachate biological treatment were uncovered through bibliometric analysis. This study also lays the groundwork for a deeper understanding of the past, current, and future trends of the leachate biological treatment. Research publications from 1974 to 2021 were retrieved from the Scopus database, and it was identified that 2013 articles were published in the span of 47 years. From the analyzed publications, China played a leading role in publishing leachate biological treatment research articles as well as having the most productive institutions and authors. Meanwhile, the USA was found to be the most active country in initiating international collaborations with 33 countries. The research hotspots were also successfully identified using keyword co-occurrences analysis. Anaerobic digestion and constructed wetland were revealed to be the research hotspots. The critical role of biological treatment in removing nitrogen from leachate was also highlighted. Besides, numerous research gaps were identified in the application of aerobic granular sludge (AGS) for leachate treatment. This can be a potential area for research in the future. Finally, future research should be encouraged to focus on the use of sustainable treatment systems in which energy recovery in the form of biogases is promoted.

The selectivity of electron acceptors for the removal of caffeine, gliclazide, and prazosin in an up-flow anaerobic sludge blanket (UASB) reactor.

This study attempts to investigate the relationship between the dominance of reducing conditions and the biotransformation of pharmaceutical compounds, which has been scarcely reported in a continuous anaerobic treatment process. Previous batch experiments have discovered the possible implications of different reducing conditions on the biotransformation process, but have failed to reflect actual removal performance due to substrate limitations and other operational factors. Continuously operating reactors commonly receive wastewater stream containing a wide range of electron acceptors that diversify the growth of microorganisms in anaerobic treatment. The alteration of the dominance of reducing conditions in a continuous anaerobic reactor may result in the improvement of biotransformation performance compared to a single reducing condition in a substrate-limited batch experiment. The removal of psychostimulant caffeine (CAF), anti-diabetic drug gliclazide (GCZ), and anti-hypertensive drug prazosin (PRZ) were examined through the operation of an up-flow anaerobic sludge blanket (UASB) reactor under predominant methanogenic condition (Phase I) and simultaneous reducing conditions provided by a nitrate supplement (Phase II). The results revealed high biotransformation performance for all three compounds (73-> 99%) in both Phase I and Phase II experiments and fitted the pseudo-first-order model. The biotransformation rate of CAF and PRZ were relatively lower by 25% and 29%, while the GCZ rate improvement doubled in Phase II compared to Phase I. The outcome from 16s rRNA sequencing suggested that the biotransformation of the compounds may be driven by Firmicutes and Bacteroidota in both phases, and Burkhorderiales and sulfate-reducing bacteria species in Phase II. This study proved preferential of reducing conditions does not negatively affect the biotransformation performance of each pharmaceutical compound in a continuous anaerobic reactor, but they led to varying biotransformation rate, hence shifting the microbial diversity.

Discovering future research trends of aerobic granular sludge using bibliometric approach.

The advantageous characteristics of aerobic granular sludge (AGS) have led to their increasing popularities among academics and industrial players. However, there has been no bibliometric report on current and future research trends of AGS. This study utilized the available reports of AGS in the Scopus database for comprehensive bibliometric analyses using VOSviewer software. A total of 1203 research articles from 1997 to 2020 were analyzed. The dominance of the Netherlands and China were revealed by the high number of publications and citations. Nevertheless, the Netherlands exhibited higher average citation per article at 76.4. A recent process of AGS involving biochar and algal addition were also identified. Meanwhile, the application of AGS for antibiotic containing wastewater as well as possibility of resource recovery were recently reported and was expected to expand in the future. It was suggested that application of AGS would develop further along with the development of sustainable wastewater treatment process.

Synthesis and characterization of Cu(OH)2-NWs-PVA-AC Nano-composite and its use as an efficient adsorbent for removal of methylene blue.

The present study focused on the synthesis of copper hydroxide nanowires decorated on activated carbon (Cu(OH)2-NWs-PVA-AC). The obtained Cu(OH)2-NWs-PVA-AC Nano-composite was distinguished by XRD, SEM, EDX, BET, FTIR and XPS respectively. Besides, different variables such as solution pH, and initial dye concentration, contact time, and temperature were performed on the adsorption efficiency of MB in a small batch reactor. Further, the experimental results are analyzed by various kinetic models via PFO, PSO, intra-particle diffusion and Elovich models, and the results revealed that among the kinetic models, PSO shows more suitability. In addition, different adsorption isotherms were applied to the obtained experimental data and found that Langmuir-Freundlich and Langmuir isotherm were best fits with the maximum adsorption capacity of 139.9 and 107.6 mg/g, respectively. The Nano-composite has outstanding MB removal efficiency of 94-98.5% with a span of 10 min. and decent adsorption of about 98.5% at a pH of 10. Thermodynamic constants like Gibbs free energy, entropy, and enthalpy were analyzed from the temperature reliance. The results reveal the adsorption processes are spontaneous and exothermic in nature. The high negative value of ΔG° (- 44.11 to - 48.86 kJ/mol) and a low negative value of ΔH° (- 28.96 kJ/mol) show the feasibility and exothermic nature of the adsorption process. The synthesized dye was found to be an efficient adsorbent for the potential removal of cationic dye (methylene blue) from wastewater within a short time.

Electro-transformation of mefenamic acid drug: a case study of kinetics, transformation products, and toxicity.

Poor removal of many pharmaceuticals and personal care products in sewage treatment plants leads to their discharge into the receiving waters, where they may cause negative effects for aquatic environment and organisms. In this study, electrochemical removal process has been used as alternative method for removal of mefenamic acid (MEF). For our knowledge, removal of MEF using electrochemical process has not been reported yet. Effects of initial concentration of mefenamic acid, sodium chloride (NaCl), and applied voltage were evaluated for improvement of the efficiency of electrochemical treatment process and to understand how much electric energy was consumed in this process. Removal percentage (R%) was ranged between 44 and 97%, depending on the operating parameters except for 0.1 g NaCl which was 9.1%. Consumption energy was 0.224 Wh/mg after 50 min at 2 mg/L of mefenamic acid, 0.5 g NaCl, and 5 V. High consumption energy (0.433 Wh/mg) was observed using high applied voltage of 7 V. Investigation and elucidation of the transformation products were provided by Bruker software dataAnalysis using liquid chromatography-time of flight mass spectrometry. Seven chlorinated and two non-chlorinated transformation products were investigated after 20 min of electrochemical treatment. However, all transformation products (TPs) were eliminated after 140 min. For the assessment of the toxicity, it was impacted by the formation of transformation products especially between 20 and 60 min then the inhibition percentage of E. coli bacteria was decreased after 80 min to be the lowest value.

The fate of prazosin and levonorgestrel after electrochemical degradation process: Monitoring by-products using LC-TOF/MS.

Prazosin (PRZ) and levonorgestrel (LNG) are widely used as an anti-disease drugs due to their biological activity in the human body. The frequent detection of these compounds in water samples requires alternative technologies for the removal of both compounds. After electrochemical degradation of PRZ and LNG, the parent compounds could be completely removed after treatment, but the identification and characterization of by-products are necessary as well. In this study, the effects of NaCl concentration and applied voltage were investigated during the electrochemical degradation process. The results revealed that the increase of NaCl concentration and applied voltage could promote the generation of hypochlorite OCl- and then enhance the degradation of PRZ and LNG. After initial study, 6V and 0.2g NaCl were selected for further experiments (96% and 99% removal of PRZ and LNG after 40min, respectively). Energy consumption was also evaluated and calculated for PRZ and LNG at 3, 6 and 8V. Solid phase extraction (SPE) method plays an important role in enhancing the detection limit of by-products. Furthermore, characterization and identification of chlorinated and non-chlorinated by-products were conducted using an accurate liquid chromatography-time of flight/mass spectrometry LC-TOF/MS instrument. The monitoring of products during the electrochemical degradation process was performed at 6V and 0.2g NaCl in a 50mL solution. The results indicated that two chlorinated products were formed during the electrochemical process. The toxicity of by-products toward E. coli bacteria was investigated at 37°C and 20hr incubation time.

Development and validation of a comprehensive solid-phase extraction method followed by LC-TOF/MS for the analysis of eighteen pharmaceuticals in influent and effluent of sewage treatment plants.

The scarcity of data about the occurrence of pharmaceuticals in water bodies in Malaysia prompted us to develop a suitable analytical method to address this issue. We therefore developed a method based on solid-phase extraction combined with liquid chromatography-time of flight/mass spectrometry (SPE-LC-TOF/MS) for the analysis of sixteen prescribed and two nonprescribed pharmaceuticals that are potentially present in water samples. The levels of these pharmaceuticals, which were among the top 50 pharmaceuticals consumed in Malaysia during the period 2011-2014, in influent and effluent of five sewage treatment plants (STPs) in Bangi, Malaysia, were then analyzed using the developed method. All of the pharmaceuticals were separated chromatographically using a 5 µm, 2.1 mm × 250 mm C18 column at a flow rate of 0.3 mL/min. Limits of quantification (LOQs) were 0.3-8.2 ng/L, 6.5-89 ng/L, and 11.1-93.8 ng/L in deionized water (DIW), STP effluent, and STP influent, respectively, for most of the pharmaceuticals. Recoveries were 51-108%, 52-118%, and 80-107% from the STP influent, STP effluent, and DIW, respectively, for most of the pharmaceuticals. The matrix effect was also evaluated. The signals from carbamazepine, diclofenac sodium, and mefenamic acid were found to be completely suppressed in the STP influent. The signals from other compounds were found to be influenced by matrix effects more strongly in STP influent (enhancement or suppression of signal ≤180%) than in effluent (≤94%). The signal from prednisolone was greatly enhanced in the STP influent, indicating a matrix effect of -134%. Twelve pharmaceuticals were frequently detected in all five STPs, and caffeine, prazosin, and theophylline presented the highest concentrations among all the pharmaceuticals monitored: up to 7611, 550, and 319 ng/L in the STP influent, respectively. To the best of our knowledge, this is the first time that prazosin has been detected in a water matrix in Malaysia. Graphical abstract ᅟ.

Producing desulfurized biogas using two-stage domesticated shear-loop anaerobic contact stabilization system.

In this study, a two-stage domesticated shear-loop anaerobic contact stabilization (SLACS) system is introduced as a new reactor design to enhance methane productivity with significant reduction in hydrogen sulphide (H2S) synthesis. Due to the rich sulfate content in industrial wastewaters, the initial fermentation phase of anaerobic digestion is highly acidifying and often leads to severe performance losses, digester's instability, and even culture crash. The SLACS system functions as a dissimilatory sulfate reduction - methanogenic reactor consisting of two compartments, a shear-loop anaerobic bed (SLAB) unit and an anaerobic plug flow (APF) unit. The functional role of the SLAB unit is not limited to acidogenesis but also sulfidogenic processes, which curtails H2S generation in the APF unit (methanogenic stage). Experimental observations indicated that pH serves a critical role in the cohabitation of acidogenic and sulfidogenic microbes in the SLAB unit. Although acidogenesis was not influenced by pH within the range of 4.5-6.0, it is vital to stabilize the pH of this unit at 5.4 to establish a steady sulfate reduction of above 75%. The highest desulfurization achieved in this compartment was 88% under a hydraulic retention time (HRT) of 4 h. With an average methane productivity of 256 mL g-1 VS, the methanogenic performance of the two-stage domesticated SLACS system shows a 32% methanogenic proficiency higher than that of the one-stage digestion system. Microbial community structure within the system carried out via Next Generation Sequencing (NGS) provided qualitative data on the sludge's sulfidogenic and methanogenic performance.

Removal of Acid Blue25 from aqueous solutions using Bengal gram fruit shell (BGFS) biomass.

The feasibility for the removal of Acid Blue25 (AB25) by Bengal gram fruit shell (BGFS), an agricultural by-product, has been investigated as an alternative for high-cost adsorbents. The impact of various experimental parameters such as dose, different dye concentration, solution pH, and temperature on the removal of Acid Blue25 (AB25) has been studied under the batch mode of operation. pH is a significant impact on the sorption of AB25 onto BGFS. The maximum removal of AB25 was achieved at a pH of 2 (83.84%). The optimum dose of biosorbent was selected as 200 mg for the removal of AB25 onto BGFS. Kinetic studies reveal that equilibrium reached within 180 minutes. Biosorption kinetics has been described by Lagergren equation and biosorption isotherms by classical Langmuir and Freundlich models. Equilibrium data were found to fit well with the Langmuir and Freundlich models, and the maximum monolayer biosorption capacity was 29.41 mg g-1 of AB25 onto BGFS. The kinetic studies indicated that the pseudo-second-order (PSO) model fitted the experimental data well. In addition, thermodynamic parameters have been calculated. The biosorption process was spontaneous and exothermic in nature with negative values of ΔG° (-1.6031 to -0.1089 kJ mol-1) and ΔH° (-16.7920 kJ mol-1). The negative ΔG° indicates the feasibility of physical biosorption process. The results indicate that BGFS could be used as an eco-friendly and cost-effective biosorbent for the removal of AB25 from aqueous solution.

Assessing the treatment of acetaminophen-contaminated brewery wastewater by an anaerobic packed-bed reactor.

The treatment of high-strength organic brewery wastewater with added acetaminophen (AAP) by an anaerobic digester was investigated. An anaerobic packed-bed reactor (APBR) was operated as a continuous process with an organic loading rate of 1.5-g COD per litre per day and a hydraulic retention time of three days. The results of steady-state analysis showed that the greatest APBR performances for removing COD and TOC were as high as 98 and 93%, respectively, even though the anaerobic digestibility after adding the different AAP concentrations of 5, 10 and 15 mg L(-1) into brewery wastewater can affect the efficiency of organic matter removal. The average CH4 production decreased from 81 to 72% is counterbalanced by the increased CO2 production from 11 to 20% before and after the injection of AAP, respectively. The empirical kinetic models for substrate utilisation and CH4 production were used to predict that, under unfavourable conditions, the performance of the APBR treatment process is able to remove COD with an efficiency of only 6.8%.

A proposed aerobic granules size development scheme for aerobic granulation process.

Aerobic granulation is increasingly used in wastewater treatment due to its unique physical properties and microbial functionalities. Granule size defines the physical properties of granules based on biomass accumulation. This study aims to determine the profile of size development under two physicochemical conditions. Two identical bioreactors namely Rnp and Rp were operated under non-phototrophic and phototrophic conditions, respectively. An illustrative scheme was developed to comprehend the mechanism of size development that delineates the granular size throughout the granulation. Observations on granules' size variation have shown that activated sludge revolutionised into the form of aerobic granules through the increase of biomass concentration in bioreactors which also determined the changes of granule size. Both reactors demonstrated that size transformed in a similar trend when tested with and without illumination. Thus, different types of aerobic granules may increase in size in the same way as recommended in the aerobic granule size development scheme.

Influence of palm oil mill effluent as inoculum on anaerobic digestion of cattle manure for biogas production.

Anaerobic digestion for palm oil mill effluent (POME) is widely known for its potential in biogass production. In this study, the potential of using cattle manure for biogas production in complete mix anaerobic bioreactor was investigated using POME at unregulated pH and temperature. Two identical bioreactors were used in this study; namely R1 and R2 fed with cattle manure without and with POME as inoculum, respectively. Both bioreactors were allowed for five days to run in batch mode followed by semi continuous operations at HRT of 20 days. R2 produced 41% methane content compared to 18% produced in R1. A better COD percentage reduction of 45% was found in R2 which was operated with POME as inoculum compared to R1 with 35%. These results indicated that POME as inoculum has an influence on the start-up time and the rate of biogas produced.This findings will help in waste reduction.

Effect of Mecoprop (RS)-MCPP on the biological treatment of synthetic wastewater in an anaerobic membrane bioreactor.

The effects of Mecoprop (RS)-MCPP were investigated in an anaerobic membrane bioreactor (AnMBr) fed with synthetic wastewater containing stepwise increases in Mecoprop concentration, 5-200 mg L(-1) over 240 days. Effects were observed in terms of soluble chemical oxygen demand (COD) removal efficiency, volatile fatty acid (VFA) production, and methane yield. Soluble COD removal efficiency was stable at Mecoprop concentrations below 200 (±3) mg L(-1), with an average of 98 (±0.7)% removal. However, at 200 (±3) mg L(-1) Mecoprop, the COD removal efficiency decreased gradually to 94 (±1.5)%. At 5 mg L(-1) Mecoprop, acetic and propionic acid concentrations increased by 60% and 160%, respectively. In contrast, when Mecoprop was increased to 200 (±3) mg L(-1), the formation and degradation of acetate was unaffected by the higher Mecoprop concentration, acetate remaining below 35 mg L(-1). Increases in the Mecoprop specific utilization rate were observed as Mecoprop was increased stepwise between 5 and 200 mg L(-1).